Fits and Tolerances for a Triplex Pump
A course build in design and making. The team picked ISO fits for each moving joint in a 3-cylinder plunger pump.
Overview
The pump has 3 cylinders in line. One crankshaft drives 3 rods. Each rod links through a wrist pin to a piston that carries a ceramic plunger. The plungers slide in a bronze head and move fluid through 3 bores. An aluminum case holds the crankshaft on 2 ball bearings and holds oil.
Two joint types share one case. Fast spinning joints need oil and space. Sliding seal joints must stay true with small play. The fit list below follows that split.
The team worked from a bought pump. They pulled it apart, measured each part, redrew each part in CAD, and set tolerances from scratch.
Try It
The home card shows the 3D model. Drag to turn. Scroll to zoom. Two clips sit with the card: an exploded view and a motion view.
The blog page itself is text only. The model and clips live on the card.
Camera starts at 50° view and fits the model to 3 units. Faces use gray metal with medium shine. If the model fails to load the card shows “Failed to load model”.
Parts
| Part | Count | Stock | Job |
|---|---|---|---|
| Wrist pin | 3 | Steel | Links rod to piston |
| Ceramic plunger | 3 | Ceramic | Moves fluid in the head bore |
| Piston | 3 | Steel | Holds the plunger, pinned to the rod |
| Crankshaft | 1 | Steel | Turns spin into back-and-forth motion |
| Connecting rod | 3 | Aluminum | Passes crank motion to the pistons |
| Head | 1 | Bronze | Holds the 3 pressure bores |
| Housing | 1 | Aluminum | Main body, holds crank bearings |
| Crankcase | 1 | Aluminum | Oil sump with side cover |
| Side covers | 2 | Steel | Close the housing ends |
| Bearing (6305) | 2 | — | Holds the crankshaft |
| Dipstick | 1 | ABS | Oil check |
The head bolts to the case with 8 M24 screws. They look large next to M6–M8 hardware elsewhere. The size holds clamp load across 3 bores under pressure.
Fit List
Each pair uses hole-basis ISO fits (ISO 286-1). The hole uses H. The shaft grade sets space or grip. Choice follows motion, not habit.
| Joint | Fit | Type | Why |
|---|---|---|---|
| Wrist pin ↔ rod small end | Ø10 H6/f6 | Loose, spins | Fast oiled spin |
| Rod big end ↔ crank pin | Ø32 H6/f6 | Loose, spins | Same oiled spin as wrist pin |
| Key ↔ keyway | Shaft N9 / Hub JS9 | Middle | Normal free key for torque |
| Bearing ↔ crank seat | Ø24 j6 and Ø25 j6 | Light grip | Maker guide for ball bearings on shafts; the two seats differ by 1 mm so each lists its own size |
| Plunger ↔ case bore | Ø20 H6/g5 | Close slide | Guides the plunger true |
| Plunger ↔ head bore | Ø15 H6/f6 | Freer slide | Fast pass through; seal comes from packing, not metal fit |
Two rules run through the list. From f to g the shaft zone moves closer to the hole. Space shrinks but stays space. g5 fits tighter than f6. It suits the guide bore where truth matters more than easy build.
Spinning oiled joints — wrist pin, big end, bearing seats — use f6 and j6. Oil parts the faces in run. The fit sets rest space and place. IT6 at the two pins pairs with N4 (Ra 0.2 µm) finish on the same prints. Fine finish needs fine grade. The two callouts back each other.
Sliding guide joints split one job in two. The case bore uses tighter g5 to keep the plunger centered. The head bore uses freer f6 because packing seals pressure there. Metal only needs smooth pass. Bronze suits ceramic here with low pick-up risk.
Shape Control
Flatness, roundness, square, place, and runout apply only where they touch work: seal faces, bearing seats, plunger bores. Other faces stay free. This keeps prints clear without loose control at key spots.
Some values run tighter than shops hold at sane cost. Roundness of 0.0002 mm on the wrist pin, and 0.00018 mm and 0.000064 mm elsewhere, read like class exercise numbers near gauge-block grade. Treat them as study values, not shop-ready callouts.
Honest Limits
Course build from a bought pump, measured and redrawn in CAD. Fit choices follow motion with hole-basis ISO classes (ISO 286-1). Shape numbers are study values, not shop-ready callouts. Wear state leaves open whether the maker bushed the rod bores. The page is text only; the model and clips live on the home card.
Next Step
Two fixes stand out:
Bushings at rod ends. As drawn the pins run straight in aluminum rod bores. Most shop pumps press a bronze or oiled sintered bushing into each rod bore. It shields soft aluminum, gives a swap wear face at the two hardest-working joints, and lets a shop recut or swap without a new rod. The sample pump shows heavy wear, which leaves open whether the maker used this fix.
Shop-true grades. Relax shape numbers to what the chosen shop holds. Pick numbers off a capability chart for the real process. Do not pinch the number until math balances.
References
- Deutsches Institut für Normung. n.d. “DIN 6885 Parallel Keys.” Accessed October 5, 2026. https://www.engineersedge.com/hardware/parallel_key_and_taper_keys_dimensions_15236.htm
- Hydraulic Institute. 2015. ANSI/HI 6.1-6.5 Reciprocating Power Pumps for Nomenclature, Definition, Application, and Operation. Hydraulic Institute.
- International Organization for Standardization. 2010. “ISO 286-1 Geometrical Product Specifications — ISO Code System for Tolerances on Linear Sizes.” https://www.iso.org/standard/45975.html
- SKF Group. n.d. “Seat Tolerances for Standard Conditions.” Accessed October 5, 2026. https://www.skf.com/group/products/rolling-bearings/principles-of-rolling-bearing-selection/bearing-selection-process/bearing-interfaces/seat-tolerances-for-standard-conditions