How Wings Make Lift, and When They Quit
Interactive NACA wing simulation. Move sliders to see lift, stall, pressure, and drag.
Overview
A wing makes lift by the pressure gradients its shape creates: air speeds up over the top, creating low pressure, and slows below, creating high pressure. Add up that pressure and you get lift. This is an oversimplification—a wing can generate lift even when the pressure below is not higher than atmospheric pressure, as long as the net aerodynamic force is upward.
How Lift Changes With Angle of Attack
As the wing’s angle of attack increases, the wing redirects the airflow more strongly, generally increasing the pressure difference between its upper and lower surfaces. Within a certain range, this makes lift increase approximately linearly with angle of attack.
For a thin airfoil at small angles, this relationship can be approximated by:
Here, (c_l) is the lift coefficient, (c_{l_0}) is the lift coefficient at zero angle of attack, and (\alpha) is the angle of attack in radians. (2\pi) is the theoretical lift-curve slope, which roughly translates to a 0.11 in lift coefficient per degree. For example, increasing the angle of attack by 3° increases the lift coefficient by roughly 0.33, provided the wing remains within its linear operating range.
The lift coefficient describes how effectively the wing generates lift, which depends on air density, flight speed, and wing area:
where (L) is lift, (\rho) is air density, (V) is airspeed, and (S) is the wing’s reference planform area.
Where camber comes in
Camber describes the curvature of an airfoil’s mean line, the line running halfway between its upper and lower surfaces. A cambered airfoil can generate lift even at zero geometric angle of attack because its shape changes the airflow and pressure distribution around it.
What happens as the angle increases?
At small angles of attack, lift generally increases approximately linearly. As the angle increases, the adverse pressure gradient near the rear of the wing can become too strong for the boundary layer to overcome, resulting in separation from the surface, reducing the wing’s ability to generate lift. Eventually, the wing reaches its stall region and, depending on the airfoil and operating conditions, the stall can develop gradually or sometimes abruptly.
What thickness changes
Airfoil thickness affects the airflow around the wing, and therefore its pressure distribution, the strength and location of pressure peaks, and how the boundary layer develops. However, thickness alone does not determine when a wing stalls.
In this model, thickness mainly affects the base drag and the shape of the airfoil. Its influence on stall is simplified: the code uses a formula to set the stall angle rather than calculating flow separation from the geometry.
Wing Shape in Four Numbers
The four-digit NACA airfoil system describes a basic airfoil profile:
- M: Maximum camber, expressed as a percentage of the chord.
- P: Position of maximum camber, measured in tenths of the chord.
- XX: Maximum thickness, expressed as a percentage of the chord.
For example, a NACA 2412 airfoil has a maximum camber of 2% of the chord, located at 40% of the chord, and a maximum thickness of 12%.
Stall
The stall region represents the regime where airflow separation reduces lift and increases drag. In the real world, stall occurs when the airflow can no longer remain sufficiently attached to sustain lift. The exact process depends on the airfoil and operating conditions.
This simulation uses a prescribed stall angle:
The angle is measured in degrees, and is the first digit of the NACA four-digit designation.
Things I learned
Must the airflow over the top and bottom of a wing meet at the trailing edge at the same time?
As it turns out, no. There is no physical rule requiring air segments that separate at the leading edge to reunite at the trailing edge at the same time.
Do real aircraft use NACA airfoils?
The Cessna 172 is one common aircraft that uses the NACA profiles. The P-51 Mustang is another famous aircraft associated with the NACA six-series airfoils. Modern aircraft have more niche needs that require finely tuned profiles that the NACA profile does not allow for.
Honest Limits
This page combines established aerodynamic concepts with simplified equations and visual approximations.
- Lift: The pre-stall relationship uses thin-airfoil theory as an approximation. Real wings may have different lift-curve slopes.
- Airfoil geometry: The four-digit NACA equations provide a standard profile, but the code’s vertical-offset construction is a simplification of the exact surface geometry.
- Stall: The stall angle is prescribed by a rule based on the camber digit, not calculated from flow separation.
- Post-stall lift: The code reduces lift after the chosen stall angle rather than solving the separated flow.
- Drag: Base drag, induced drag, and post-stall drag use simplified formulas. The model fixes the span efficiency factor at 1 and the aspect ratio near 6.
- Pressure: The displayed pressure curves are sketched from simple rules rather than computed by solving the flow around the wing.
The purpose is to illustrate how airfoil shape, angle of attack, lift, drag, pressure, and stall relate to one another. The results should not be treated as engineering predictions for a real wing.
References
- Abbott, Ira H., and Albert E. von Doenhoff. 1959. Theory of Wing Sections. Dover.
- Anderson, John D. 2017. Fundamentals of Aerodynamics. 6th ed. McGraw-Hill.
- Jacobs, Eastman N., Kenneth E. Ward, and Robert M. Pinkerton. 1933. “The Characteristics of 78 Related Airfoil Sections from Tests in the Variable-Density Wind Tunnel.” NACA Report 460.
- Milne-Thomson, Louis M. 1966. Theoretical Aerodynamics. 4th ed. Macmillan.